Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Atlanta Homeowners Choose DuraFlex Chimney Cleaning
We provide Atlanta Duraflex service for homes with DuraFlex Pro, SW, 316, and AL liner systems. Our techs work on these corrugated stainless liners daily, so we know exactly where creosote hides, which caps clog, and when a liner section needs replacing rather than patching. We’re not affiliated with or authorized by DuraFlex, and we’ll tell you that straight. What we are is a chimney company that carries DuraFlex-compatible sizing, tees, and termination caps on the truck, so the inspection and cleaning happen the same visit, not three weeks later. Call (762) 356-6423 for a DuraFlex-specific quote.
Ruben Castellano founded Alcott Chimney Atlanta to fix what frustrated him about the trade: technicians who couldn’t explain what they found, and pricing that shifted after the work started. That’s why every DuraFlex job here gets a written price before we touch the liner, a named and photo-verified technician before arrival, and a written guarantee on any repair we make. If a repair fails within 365 days, we return free. That’s the Done Right Promise, and it covers DuraFlex work just like everything else.
Why Trust Alcott Chimney Atlanta for Your DuraFlex Chimney Cleaning?
DuraFlex liners have a corrugated inner wall, and that’s the whole ballgame. Smooth-wall liners shed creosote differently. Corrugated liners trap it at seam joints, at offsets, and where the liner meets the tee. A chimney sweep who treats a DuraFlex liner like any other tube will miss buildup that a trained eye catches in the first ten minutes. Our technicians have spent years pulling caps off Atlanta chimneys and reading exactly what the corrugation pattern is telling them. The rough spot near an elbow? That’s a seam catching particulate. The heavy accumulation around the tee snout? Condensate dripping back down the liner and pooling. We know these patterns because we see them every week in Grant Park bungalows, Duraflex repair in Decatur, and everywhere in between.
Ruben Castellano brought his crew east after years working West Coast chimneys, and Atlanta’s humidity taught him things Los Angeles never did. The way moisture interacts with creosote here, the pollen load that clogs termination caps in spring, the red clay soil that settles foundations and shifts liner alignment. He’ll walk you through what the camera shows inside your flue before quoting a single dollar. That’s how this company has operated since 2002, and it’s why we carry genuine DuraFlex components plus matched aftermarket equivalents for routine access and sealing work.
Styles & brands we work with
Common DuraFlex Chimney Cleaning Problems We Fix in Atlanta
- Creosote packed at the first elbow on DuraFlex Pro liners. The Pro series handles wood-burning appliances, and Atlanta’s mild winters mean long, slow burns that produce sticky, tar-like creosote. It collects where the liner changes direction. We use drill-powered rotary brushes sized to the liner ID to break it loose, then pull the tee cap and vacuum everything out through the snout.
- Tee snout and cleanout cap collecting soot and condensate. Every DuraFlex system has a tee at the base where the liner meets the appliance connector. Moisture and soot settle there. If the cleanout cap hasn’t been pulled in years, you’ll see a solid cake of black sludge. We detach the lower tee, empty it fully, and replace the cap with the correct DuraFlex component for your liner diameter.
- Pinholes or seam separation at offsets on older 316 liners. DuraFlex 316 is rated for wood, pellet, and some gas applications, but age and installation stress can open tiny holes at the corrugation seams, especially where the liner bends through an offset. During a Level 2 inspection, our camera shows us exactly where these are. When the metal is that far gone, patching is a waste of your money. We’ll tell you straight whether a re-sleeve makes more sense.
- Termination cap mesh clogged with Atlanta pollen and leaf debris. April in Atlanta coats everything in yellow-green pollen, and DuraFlex cap mesh catches it like a net. Add spring oak leaves and summer humidity that cakes the debris in place, and airflow drops fast. We clean or replace the cap and check the mesh gauge against what your appliance actually needs. Too fine a mesh clogs faster; too coarse lets embers through.
- Rough interior spots on 316 SW liners catching creosote before it exits. The SW line is a heavier, smoother variant, but even SW develops wear patterns. When creosote catches on a rough patch, it builds outward and narrows the flue passage. Routine cleaning keeps those spots from becoming blockages. If we see a rough area that’s losing metal thickness, we document it with the camera and put it in your report so you can make a decision with eyes on the evidence.
DuraFlex Parts & Our Repair-vs-Replace Approach
When you need replacement parts for a DuraFlex system in Atlanta, the first question is whether genuine components are available locally. We stock common DuraFlex tees, caps, and connectors on our trucks because waiting on a distributor order while your fireplace sits cold is not how we work. For routine sealing and access components, we’ll quote a quality aftermarket equivalent only if it matches your liner’s inner diameter and fuel type exactly. We will not substitute a wood-rated part for a gas application, ever.
Here’s the honest part: some liner sections are too far gone to patch. Welding or banding an old corrugated 316 tube that’s riddled with pinholes is throwing good money at bad steel. When that’s what the camera shows, we say so. A re-sleeve with a new DuraFlex liner section is often safer, faster, and honestly cheaper over five years than nursing a failing tube. Call (762) 356-6423 for a straight answer on your liner.
Our DuraFlex Service Process – Step by Step
- 1
Diagnosis. We run a camera through the full DuraFlex liner from the cap down through the tee and cleanout. You see the footage on the spot. No recommendations without visual proof you’ve seen yourself.
- 2
Repair or install. If we’re re-sleeving or replacing a section, we match the liner ID and fuel rating to your existing DuraFlex system. Genuine components where they matter; matched aftermarket only where equivalent is genuinely equivalent.
- 3
Test. After cleaning or repair, we check draft at the appliance and verify the termination cap is clear and correctly rated. If it’s a gas system, we confirm the connector seals are tight and the liner is sized for the BTU load, not just the old pipe diameter.
- 4
Warranty. Every repair gets a written guarantee. If it fails within 365 days, the second visit is free. That’s the Done Right Promise, and it applies to DuraFlex work exactly like every other repair we make.
See the difference
Before
After
Before
After
Before
AfterDuraFlex Products We Service & Install in Atlanta
We clean, inspect, and install across the DuraFlex lineup: the Pro series for wood-burning appliances, the SW heavier-gauge liner for demanding installs, the 316 multi-fuel liner common in Atlanta’s older retrofit chimneys, and the AL aluminum liner for gas appliances. We carry sizing tees, termination caps, and connectors for the most common Atlanta configurations on our trucks, so most jobs finish in one visit. Every install starts with a written quote and ends with the same 365-day guarantee.
We Also Service These Brands
DuraFlex is a big part of our work, but it’s not the whole job. We also service and install HeatShield resurfacing systems and Gelco products, plus other professional trade materials like Olympia Chimney, Famco, and Copperfield. If your chimney has mixed-brand components, we can handle the whole system without bouncing you between specialists.
FAQs – DuraFlex Chimney Cleaning Service in Atlanta
The rough spot you’re feeling is almost always wear at a corrugation seam, where a slight manufacturing irregularity or installation stress gives creosote a place to grab. Once it catches, it grows. A camera inspection shows us whether it’s surface roughness or actual metal loss. Surface roughness is a cleaning issue. Metal loss is a replacement issue. Call (762) 356-6423 and we’ll put eyes on it.
Yes, and that’s the only way we do Level 2 inspections. The camera runs the full length of the liner, through the tee body, and down to the cleanout. Most problems we find in Atlanta chimneys are at the base, not the middle of the tube, so skipping the tee inspection misses the point. We also pull the cleanout cap and check what’s settled there. You’ll see the footage yourself.
When a factory DuraFlex tee cap is available locally and matches your liner diameter, that’s what goes on. For routine replacements where a genuine cap isn’t immediately available, we’ll offer a quality aftermarket equivalent that matches the ID and fuel type. We always tell you which one you’re getting and why, before the part goes in.
That depends on the liner’s condition and diameter, not just its grade. The SW line is built heavier, but a gas insert conversion changes the exhaust temperature and moisture profile inside the liner. If the existing SW liner is structurally sound and correctly sized for the insert’s BTU output, it can often be reused. If the camera shows seam wear or the diameter is wrong for the new appliance, we’ll recommend re-sleeving instead. Get a Level 2 inspection before you commit to a conversion.
We replace the cap before or during the cleaning, not after. A damaged mesh changes how much air moves through the liner during the sweep and lets debris fall inside. We’ll remove the old cap, inspect the top section of the liner, install the correct replacement, then run the rotary brush down through the full system. You get a clean liner and a cap that actually vents.
A standard DuraFlex chimney cleaning in Atlanta typically runs $189 – $329 depending on liner length, accessibility, and whether we’re also pulling the tee and cleanout for a full service. Repair work is quoted separately after diagnosis and always in writing before any work starts. Call (762) 356-6423 for an exact quote. Estimates are free.
Book Your DuraFlex Service in Atlanta, GA
If your DuraFlex liner needs cleaning, inspection, or repair in Atlanta, call (762) 356-6423. A live person answers around the clock. You’ll get a written price before work starts, a technician you’ve already seen by name and photo, and a written guarantee on any repair we make. If the repair fails within 365 days, the second visit is free.
Written by Ruben Castellano, Owner at Alcott Chimney Atlanta, serving Atlanta since 2002.